Illuminating | Home

IMAL05 LED Area Light 100-300W

Description:

Contact Us

Construction

  • Rugged one-piece, die-cast aluminum housing secures the thermally conductive LED panel and electrical chamber
  • Low profile, 3G vibration rated compact design minimizes wind load requirements.
  • Housing is completely sealed against moisture and environmental contaminants.

Notes: Actual performance may differ as a result of end-user environment
and application. All values are design or typical values, measured
under laboratory conditions at 25℃(±5℃ ) specifications subject to
change without notice.

Optics

  • Available in IES Type III, IV, V distributions
  • Light engines are available in standard 4000 K and 5000 K (70 CRI) configurations.
  • Scalable Lumen Packages from 13,900 to 42,000 Lumens replaces up to 1000W Metal Halide.
  • Optics is precisely designed to shape the distribution, maximizing efficiency and application spacing.
  • The optics can conform to dark sky requirement.
  • For the ultimate level of spill light control, an optional house-side shield accessory can be field or factory installed.

Electrical

  • Universal 120-277 VAC or 347-480 VAC input voltage
  • Standard with 0-10V dimming driver for 10% to 100% dimming capabilities.
  • Power adjustable: 100%, 80%, 60%, 40%.
  • THD: ≤20%
  • Power Factor: ≥90%

Controls

  • Optional Occupancy sensor or Microwave sensor or daylight sensor.
  • Optional Bluetooth sensor or Bluetooth controller.
  • Silvair Luminaire Level Lighting Control (LLLC) optional.
  • Sharkward Luminaire Level Lighting Control (LLLC) optional.
  • Also compatible with 3rd party smart network control system.
  • Optional NEMA 3-pin photocell or 7-pin photocell

Ambient Temperature:

  • Ambient operating temperature -40˚ C to 40˚ C (-40℉ to 104℉).

Installation

  • Suitable for mounting heights ranging from 26-50’ in area lighting applications
  • Round pole, Square pole, slipfitter, wall mount and yoke are available.
  • The design can be operated by one person to install the whole lamp

Lifespan

  • Estimated 100,000-hour LED lifespan based on IES LM-80 results and TM-21 calculations

Finish

  • It's available in black or optional dark bronze, silvery gray or white.

Certifications

  • DesignLights Consortium™ Qualified.
  • UL cUL wet location listed.

Note:DesignLights Consortium™ Qualified and classified for DLC Premium (all lumen packages),refer to www.designlights.org for details.

Notes:Actual performance may differ as a result of end-user environment
and application. All values are design or typical values, measured
under laboratory conditions at 25℃(±5℃ ) specifications subject to
change without notice.

Applications

Auto dealerships, parking lots, walkways, roadways, campuses, facade lighting, grocery stores and other public areas.

PERFORMANCE DATA

ELECTRICAL DATA

EPA OF AREA LIGHT

Item

1

2 @90°

2 @120°

2@180°

3 @90°

3 @120°

4 @90°

100W

0.2751

0.5267

0.7321

0.6164

0.9577

0.9837

0.9577

150W

0.3111

0.6343

0.6464

0.6222

0.9335

0.9696

0.9335

250W/300W

0.4097

0.7227

0.9919

0.8856

1.1986

1.3049

1.1986

 

BUG

MOUNTING

  • Standard versatile mounting arm accommodates multiple drilling patterns as well as square and round poles
  • Optional for cast aluminum slipfitter mounting adapter(Compatible with more mounting adaptors such as Tenon, suits for various application)

Mounting Options

Arm Mount

(4"and 5"Square and Round poles) Standard versatile mounting arm is simple to install and can be used with existing poles for retrofit installations.

Slipfitter Mount

An optional cast aluminum mast arm adapter secures fixture head to nominal 2-3/8''O.D. horizontal steel tenon arm.

Wall Mount

Wall Mount is easy to install for direct wall mounting with 1/2' conduit wiring or standard J-box mounting

Yoke Mount

Die-cast aluminum trunnion is easily adapted to many surfaces and allows easy fixture aiming angles.

Adjustable Arm Mount

Standard versatile mounting arm is simple to install and can be used with existing poles for retrofit installations.

 

Mounting Dimensions

PHOTOMETRICS

Offers a complete set of optical systems to meet every site lighting requirement. These systems provide remarkable flexibility in precisely matching light distribution patterns to specific site requirements.

Type 3 optics produce an asymmetrical pattern that directs the majority of the light forward and equally on both sides of the luminaire. In a back-to-back configuration, it creates a rectangular pattern which can extend pole spacings.

Type 4 is suitable for applications where light is primarily required forward with minimal backlight. Typical installations include perimeter poles.

 

Type 5 optics produce a symmetrical square distribution pattern that distributes light equally on all sides of the luminaire. Type 5 luminaires is universal for most area lighting applications

 

DIMENSION

Order Guide

ADDITIONAL MOUNTING ACCESSORIES

Pole Bracket 

  • For mounting one fixture on an existing pole

4" Square Pole Mount with 2-3/8" O.D. Tenon

No. 4SQ-SP-D

Finish: Dark Bronze

USE: For use with square, non-tapered steel and aluminum poles. Furnished with four 5/16" hex head stainless-steel bolts. Vertical tenon measures 2-3/8" O.D., and is made of steel tubing. Fixtures mounted to this bracket can be adjusted both vertically and horizontally.

4" Round Pole Mount with 2-3/8" O.D. Tenon

4SQR-SP-D

Finish:Dark Bronze

USE: For use with Round, non-tapered steel and aluminum poles. Furnished with three 3/8" hex head stainless-steel bolts. Vertical tenon measures 2-3/8" O.D., and is made of steel tubing.

Fixtures mounted to this bracket can be adjusted both vertically and horizontally.

5" Square Pole Mount with 2-3/8" O.D. Tenon

No. 5SQ-SP-D

Finish: Dark Bronze

USE: For use with square, non-tapered steel and aluminum poles. Furnished with four 5/16" hex head stainless-steel bolts. Vertical tenon measures 2-3/8" O.D., and is made of steel tubing. Fixtures mounted to this bracket can be adjusted both vertically and horizontally.

5" Round Pole Mount with 2-3/8" O.D. Tenon

5SQR-SP-D

Finish:Dark Bronze

USE: For use with Round, non-tapered steel and aluminum poles. Furnished with three 3/8" hex head stainless-steel bolts. Vertical tenon measures 2-3/8" O.D., and is made of steel tubing.

Fixtures mounted to this bracket can be adjusted both vertically and horizontally.

Pole Bracket Accessories –Angle-Adjustment Adapter

SQA-ALDA

Finish: Dark Bronze

USE: Durable brackets are engineered to provide versatile mounting options. These arms are made from rugged die-cast aluminum. They allow optimal positioning of the light fixture to maximize the lighting effectiveness vertically and horizontally.

Pole Bracket accessories-Tenon & Yoke Adaptor

SP-TR-D

Finish: Dark Bronze

USE: The 2-3/8” OD Tenon Mount Adaptor for Yoke Fixtures is designed to mount light fixtures that are equipped with

a yoke mount onto a 2-3/8” OD tenon. It may be utilized with the Flood Light Series of light fixtures.

Wall Bracket:

  • Attaches to any flat surface.

  • Provides wiring access

90° Wall Mount Bracket with 2-3/8" O.D. Tenon

WM-SP-D

Finish: Dark Bronze

USE: The 90˚ wall mount bracket with 2-3/8" tenon attaches an floodlight to almost any surface: wall, roof, or wood pole.

Provides wiring access and abuilt-in 2-3/8" O.D. tenon to mount a fixture with our adjustable slipfitter. Suggested 3/8" diameter bolts for mounting. Mounting holes are spaced 3-1/4" apart.

Mid-Pole tenon Bracket:

2-3/8” OD Horizontal Tenon Mid-Pole Bracket

SQ-SP-D

Finish:Dark Bronze

USE:2-3/8” OD Horizontal Tenon Mid-Pole Bracket is designed to mount light fixture that is equipped with a adjustable slipfitter onto a 2-3/8” OD horizontal tenon

 

Round External Mount Horizontal Tenon

  • · To mount 2/3/4 fixtures on a existing pole

Double 90‘ Horizontal Tenon Adaptor

R60-SP2-90-D

Finish:Dark Bronze

USE:The Bracket is designed to mount over 2-3/8” (60mm) O.D. vertical tenon. Two fixtures can be mounted to the Round External Mount Horizontal Tenon and adjusted horizontally

Triple 120’ Horizontal Tenon Adaptor

R60-SP3-120-D

Finish:Dark Bronze

USE:The Bracket is designed to mount over 2-3/8” (60mm) O.D. vertical tenon. Three fixtures can be mounted to the Round External Mount Horizontal Tenon and adjusted horizontally

Double 180‘ Horizontal Tenon Adaptor

R60-SP2-180-D

Finish:Dark Bronze

USE:The Bracket is designed to mount over 2-3/8” (60mm) O.D. vertical tenon. Two fixtures can be mounted to the Round External Mount Horizontal Tenon and adjusted horizontally

Quad 90’ Horizontal Tenon Adaptor

R60-SP4-90-D

Finish:Dark Bronze

USE:The Bracket is designed to mount over 2-3/8” (60mm) O.D. vertical tenon. Four fixtures can be mounted to the Round External Mount Horizontal Tenon and adjusted horizontally

Triple 90’ Horizontal Tenon Adaptor

R60-SP3-90-D

Finish:Dark Bronze

USE:The Bracket is designed to mount over 2-3/8” (60mm) O.D. vertical tenon. Three fixtures can be mounted to the Round External Mount Horizontal Tenon and adjusted horizontally

 

IMAL05 LED Area Light 100-300W